Measuring made easy

How to Measure for Your Iron Door

You don’t need to be a contractor — or pry off a single piece of trim. With a tape measure and about ten minutes, you can find your size by measuring the door you already have. Here’s exactly how.

A home front entrance with a wrought-iron double door and transom

First — how our doors are sized

Every iron door is sized by the outside of its frame — the outer edge of the steel frame that surrounds the door — written as width × height in inches (for example, 38 × 96). Width always comes first.

That’s a bit larger than the door you see today, and a bit smaller than the framed hole in your wall (your “rough opening”). The good news: nearly every home is framed the same way, so you can figure out your frame size just from the door you already have — no prying off trim.

A single iron door with its height and width labeled, measured to the outside of the frame
Our doors are measured by the outside of the frame — the full width and height, edge to edge.

The easy method — measure what you can see

1

Measure your existing door

Open the door and measure the door panel itself — the part that swings, edge to edge. Take the width at the top, middle, and bottom, and the height on both sides and the center. Write down the smallest number for each, to the nearest ⅛″.

2

Add the frame

Our size is the outside of the steel frame that wraps the door — a little bigger than your door on every side. A simple rule of thumb:

  • Width = your door width + about 2″
  • Height: a standard 6’8″ (80″) door → our 81″ size; an 8-foot (96″) door → our 96″ size

Example: a common 36 × 80 front door → a frame size of about 38 × 81.

3

Match it to our sizes

Match your frame size to the nearest below. Between two sizes, or want a taller, grander entry? That’s a Special Order or Custom Door.

Your existing door Our size (frame outside)
36 × 80 — standard single 38 × 81
36 × 96 — 8-ft single 38 × 96
~44″ wide single 46 × 96
Double, ~59″ across both doors, 80″ tall 61 × 81
Double, ~59″ across both doors, ~92″ tall 61 × 93
Double, ~60″ across both doors 62 × 96
Double, ~70″ across both doors 72 × 81 / 72 × 96

Double doors: measure straight across both panels together, then add about 2″ for the frame width.

What about the hole in the wall? Your rough opening should be about ½″–1″ larger than the frame size you order, so the door slides in and shims snug. You order by the frame size above — not the rough opening. If your opening is tight, size down and we’ll make it work.

Which way does your door swing?

While you’re there, note your door’s swing. It’s built into the frame, so it has to be right when you order.

  • Stand outside, facing the door.
  • Hinges on your left = Left. Hinges on your right = Right.
  • Opens away from you, into the house = In-swing. Opens toward you = Out-swing.

Example: hinges on the right and the door pushes into the house → Right In-swing, our most common.

Left in-swing iron door: hinges on the left as seen from outside, door opens into the house
Left In-swing — hinges on the left, opens into the house
Right in-swing iron door: hinges on the right as seen from outside, door opens into the house
Right In-swing — hinges on the right, opens into the house (most common)
Left out-swing iron door: hinges on the left as seen from outside, door opens outward
Left Out-swing — hinges on the left, opens out toward you
Right out-swing iron door: hinges on the right as seen from outside, door opens outward
Right Out-swing — hinges on the right, opens out toward you

A 30-second gut check

Glance at your door frame. If it’s a normal wood frame (about ¾″ thick) wrapped in trim — like the vast majority of homes — the numbers above hold. If you have an unusually thick or masonry (brick) frame, sidelites (glass panels beside the door), or a transom (window above), snap a photo and we’ll size it with you.

A few pro tips

  • Measure to your finished floor. Planning new tile or hardwood? Add that thickness into your height now.
  • Always record to the nearest ⅛ inch, and use the smallest of your three readings.
  • When in doubt, size down and let us confirm — a slightly smaller frame shims snug, but one that’s too big simply won’t fit.
Not 100% sure? That’s completely normal. Send us your door measurements and a quick photo of the opening, and we’ll confirm your exact size — and flag it if you’d be better off with a custom door. Send my measurements →